人工点胶灌胶：人工搅拌胶水只能在操作范围完成，手工搅拌胶水会不断有气泡进去，而且胶水流动性会越来越差，胶量不好控制，灌到产品上气泡不容易消除。
Artificial glue irrigation: artificial mixing glue can only be completed in the operation range, hand stirring glue will continue to have bubbles, and the glue flow will become worse and worse, the amount of glue is not well controlled, and the bubble is not easy to remove.
桌面型点胶灌胶机
设备点胶灌胶：点胶灌胶机操作流程，AB胶分别自动抽料至点胶灌胶机的料缸同时抽真空，确保单组份胶水没有气泡。机器整个过程都有密封的，混合后的胶水无汽泡。表面光滑，点胶灌胶量非常精确的，设备是按自动比例出来后再混合，刚混合好的胶水都是流动性较好的胶水，出胶总量、出胶速度可调。一直操作机器不需要清洗，超过胶水可操作时间30分钟后进行自动清洗。
Equipment dispensing and glue filling: dispensing and glue filling machine operation process, AB glue are automatically pumped to the machine cylinder at the same time vacuum, to ensure that the single component glue without bubbles. The whole process of the machine is sealed, and the glue is mixed without bubbles. The surface is smooth and the amount of glue is very accurate. The equipment is then mixed according to the automatic proportion. The glue which has just mixed is good liquid glue, the total amount of glue out and the speed of glue out can be adjusted. The machine has been operated without cleaning, and it can be cleaned automatically after 30 minutes.
点胶灌胶系统延升的问题：关于换胶水的问题，点胶灌胶系统是可调的，通过马达控制计量泵的转速控制出胶，转多少圈出多少克胶水。机器一般按胶水的比例定做，所有管路及计量泵都按比例做，这样可以延长使用寿命及确保精度。
Gluing system extension problem: on the problem of glue exchange, the glue dispensing system is adjustable, through the motor control the speed of the pump to control the glue, how much to circle the amount of glue. The machine is generally customized according to the proportion of glue, all pipelines and metering pumps are done according to the proportion, which can extend the service life and ensure accuracy.
一般见议一套设备用一款胶水，不见议反反复复一台点胶机同时用几款胶水，因为清洗会比较麻烦，所有经过胶水的部件都需要清洗，特别是计量泵及管路如果没有清洗干净，部份胶水会中毒不干。如果真的要更换另一款胶水，大概花半天时间把压力桶、计量泵、枪阀全部清洗干净，管路见议重新更换，比例直接在系统里面调节即可。
Generally speaking, a set of equipment for a set of glue, do not see the review and recovery of a machine at the same time a few glue, because the cleaning will be more troublesome, all the parts through the glue need to be cleaned, especially if the metering pump and pipeline are not cleaned, part of the glue will be poisoned and not dry. If you really want to replace another glue, it will take about half a day to clean all the pressure barrel, metering pump and gun valve. The pipeline is replaceable, and the proportion is directly adjusted in the system.
